Numerical Solution for Thermal Elastohydrodynamic Lubrication of Line Contact with Couple Stress Fluid as Lubricant

Updata:01-01-1970

Source:
By:Vishwanath B. Awati, Mahesh Kumar N, N. M. Bujurke

DOI: https://doi.org/10.30564/jmmmr.v6i1.5396

Abstract:

In this paper, the detail analysis of the influence of thermal and non-Newtonian aspects of lubricant (couple stress fluid) on EHL line contact as a function of slide-roll ratio is presented. The novel low complexity FAS(Full approximation scheme), of  Multigrid scheme, with Jacobi dipole and Gauss Seidel relaxationis used for the solution of coupled equations viz.modified Reynolds equation, film thickness equation and energy equation satisfying  appropriate boundary conditions. The analysis reveals the combined influence of non-Newtonian, thermal and slide-roll ratio (of bearing movingwith different speeds) on pressure, film thickness and pressure spike covering wide range of physical parameters of interest. Results show that pressure spike is strongly influenced by thermal, slide-roll ratio and non-Newtonian character of lubricant with negligible effect on overall pressure distribution. Also, minimum film thickness is slightly altered and it increases with increase in couple stress parameter. These findings confirm the importance of non-Newtonian and thermal effects in the study of EHL.

References:

[1] Dowson, D., Higginson, G.R., 1997. Elastohydrodynamic lubrication, second edition. Pergamon Press: Oxford. [2] Hamrock, B.J., Tripp, J.H., 1983. Numerical methods and computers used in Elastohydrodynamic lubrication. Proceedings 10th leeds Lyon Symposium, Tribology. Butterworth Scientific Ltd.: London. pp. 11-19. [3] Dowson, D., Ehrel, P., 1999. Present and future studies in Elastohydrodynamic lubrication. Proceedings of the Institution of Mechanical Engi￾neers Part J-Journal of Engineering Tribology.213, 317-333. [4] Schlijper, A.G., Series, L.E., Rycrist, J.E., 1996. Current tools and techniques in EHL modeling. Tribology International. 29(8), 669-673. [5] Spikes, H.A., 2006. Sixty years of EHL. Lubrication Science. 18, 265-291. [6] Lugt, P.M., Morales-Espejel, G.E., 2011. A review of Elastohydrodynamic theory. Tribology Transaction. 54, 478-496. [7] Venner, C.H., 1991. Multilevel solution of the EHL line and point contact problems [PhD thesis]. Netherland: Twente University. [8] Goodyer, C.E., 2001. Adaptive numerical methods for EHL [PhD thesis]. Leeds: University of Leeds. [9] Petrusevich, A.I., 1951. Fundamental conclusions from the contact hydrodynamic theory of lubrication. IZV.Akad. Mank, SSSR (Ctal). 2, 209-223. [10]Okamura, H.A., 1982. Contribution to the numerical analysis of isothermal elastohydrodynamic lubrication. Tribology of reciprocating rngines. Proceedings of the 9th Leeds-Lyon Symposium on Tribology. Butterworth Scientific Ltd.: London. pp. 313-320. [11] Lubrecht, A.A., Ten Napel, W.E., Bosma, R., 1986. Multigrid, an alternating method for calculating film thickness and pressure profiles in elastodyrodynamically lubricated line contacts. Journal of Tribolgy. 108, 551-556. [12]Brandt, A., 1984. Multigrid Techniques: 1984, Guide with application to fluid dynamics. GMD Bonn. [13]Brandt, A., Lubrecht, A.A., 1990. Multilevel matrix multiplication and fast solution of integral equations. Journal of Computational Physics. 90, 348-370. [14]Venner, C.H., Ten Napel, W.E., Bosma, R., 1990. Advanced multilevel solution of the EHL line contact problem. Transaction of the ASME. 112, 426-432. [15]Bujurk, N.M., Shettar, B.M., Kantli, M.H., 2017. Wavelet preconditioned Newton-Krylov method for EHL line contact problems. Applied Mathematical Modeling. 46, 285-298. [16]Bell, J.C., 1962. Lubrication of rolling surfaces by a Ree-Eyring fluid. ASLE Transactions. 5, 160-171. [17]Houpert, L.G., Hamrock, B.J., 1985. Elastohydrodynamic lubrication calculation used as a tool to study scffing. Proceedings 12th Leeds Lyon symposium on Tribology. Butterworth Scientific Ltd.: London. pp. 146-159. [18]Conry, T.F., Wang, S., Cusano, C., 1987. A Reynolds-Eyring equation for elastohydrodynamic lubrication in line contacts. Transaction ASME, Journal of Tribology. 109, 648-658. [19]Jacobson, B.O., Hamrock, B.J., 1984. Non-Newtonian fluid model incorporated into elastohydrodynamic lubrication of rectangular contacts. ASME Journal of Tribology. 106(2), 275-284. [20]Zhu, W.S., Neng, Y.T., 1988. A Theoretical and experimental study of EHL with grease. Transaction ASME Journal of Tribology. 110, 38-43. [21]Bujurke, N.M., Shettar, B.M., Hiremath, P.S., 2018. A novel numerical scheme for the analysis of effects of surface roughness on EHL line contact with couple stress fluid as lubricant. Indian Academy of Sciences, Saadhana. 43, 1-22. DOI: https://doi.org/10.1007/s12046-018-0906 [22]Wang, S.H., Hua, D.Y., Zhang, H.H., 1988. A full numerical EHL solution for the line contacts under pure rolling condition with a Non-Newtonian Rheological Model. Journal of Tribology. 110(4), 583-586. [23]Chippa, S.P., Sarangi. M., 2013. Elastohydrodynamically lubricated finite line contact with couple stress fluids. Tribology International. 67, 11-20. [24]Das, N.C., 1997. Elastohydrodynamic lubrication theory of line contacts couple stress fluid model. Tribology Transaction. 40, 353-359. [25]Saini, P.K., Kumar, P., Tandon, P., 2007. Thermal elastohydrodynamic lubrication characteristics of couple stress fluid in rolling/sliding line contacts. Proceedings of the Institution of Mechanical Engineers—Part J, Journal of Engineering Tribology. 221, 141-153. [26]Kantli, M.H., Shettar, B.M., Bujurke, N.M., 2017. Jacobian free Newton-GMRES method for analyzing combined effects of surface roughness and couple stress character of lubricant on EHL line contact. INSA. 83, 175-196. [27]Bujurke, N.M., Kantli, M.H., Shettar, B.M., 2018. Jacobian free Newton-GMRES method for the solution of elastohydrodynamic grease lubrication in line contact using wavelet based preconditioner. Proc. Acad. Sci. A Phy. Sci. 88(2), 247-265. [28]Awati, V.B., Shankar, N., Mahesh Kumar, N., 2016. Multigrid method for the EHL line contact with bio-based oil as lubricant. Applied Mathe￾matics and Nonlinear Science. 1(2), 359-368. [29]Awati, V.B., Shankar, N., Mahesh Kumar, N., 2018. Multigrid method for the solution of EHL point contact with bio-based oil as lubricants for smooth and rough asperity. Industrial Lubrication and Tribology. 70(4), 599-611. DOI: https://doi.org/10.1108/ILT-12-2016-0314 [30]Awati, V.B., Shankar, N., 2018. An Isothermal Elastohydrodynamic lubrication of elliptical contact with multigrid method. Australian Journal of Mechanical Engineering. 18(3), 375-384. DOI: https://doi.org/10.1080/14484846.2018.1531810 [31]Sternlicht, B., Lewis, P., Flynn, P., 1961. Theory of lubrication and failure of rolling contacts. ASME Transaction of Tribology. 83, 213-226. [32]Cheng, H.S., Sternlicht, B., 1965. A numerical solution for the pressure, temperature and film thickness between two infinitely long, lubricated rolling and sliding cylinders, under heavy loads. Journal of Basic Engineering. 87, 695-707. [33]Dowson, D., Whitaker, A.V., 1968. A numerical procedure for the solution of the elastohydrodynamic problem of rolling and sliding contact lubricated by a Newtonian fluid. Proceedings of the Institution of Mechanical Engineers. 182, 119-134. [34]Murch, L.E., Wilson, W.R.D., 1975. A thermal elastohydrodynamic inlet zone analysis. ASME Journal of Lubrication Technology. 97, 212-216. [35]Ghosh, M.K., Hamrock, B.J., 1985. Thermal elastohydrodynamic lubrication of line contacts. ASLE Transaction. 28, 159-171. [36]Sadeghi, F., Sui, P.C., 1990. Thermal elastohydrodynamic lubrication of rolling/sliding contacts. ASME Journal of Tribology. 112, 189-195. [37]Houpert, L.G., Hamrock, B.J., 1986. Fast approach for calculating film thickness and pressures in elastohydrodynamically lubricated contacts at high load. Journal of Tribology. 108, 411-420. [38]Yang, P.R., Wen, S.H., 1992. The behavior of non-Newtonian thermal EHL film in line contacts as dynamic loads. ASME, Journal of Tri￾bology. 114, 81-85. [39]Wolff, R., Nonaka, T., Kubo, A., et al., 1992. Thermal elastohydrodynamic lubrication of rolling/sliding line contacts. ASME Journal of Tribology. 114, 706-713. [40]Wolff, R., Kubo, A., 1994. The application of Newton-Raphson method to thermal elastohydrodynamic lubrication of line contacts. ASME Journal of Tribology. 116, 733-740. [41]Hsiao, H.S., Hamrock, B.J., 1994. Non-Newtonian and thermal effects on film generation and traction reduction in EHL line contacts conjunction. ASME Journal of Tribology. 116(4), 794-823. [42]Yang, P., Wang, T., Kaneta, M., 1994. Thermal and non-Newtonian numerical analysis for starred EHL line contact. ASME Journal of Tribology. 128(2), 282-298. [43]Salehizadeh, H., Saka, N., 1991. Thermal non-Newtonian elastohydrodynamic lubrication of rolling line contacts. ASME, Journal of Tribology. 113, 481-491. [44]Liu, Z., Picken, D., He, T., et al., 2018. A thermal EHL model for connected rollers and its application on open seal-Houling interface. Journal of Tribology. 30, 1-34. [45]Briggs, W.L., Henson, V.E., McCormick, S.F., 2000. A multigrid tutorial, second edition. SIAM: Philadelphia. [46]Roelands, C.J.A., 1966. Correlation aspects of viscosity-temperature-pressure relationship of lubricating oils [PhD thesis]. Netherlands: Delft University of Technology. [47]Wang, S.H., Zhang, H.H., 1987. Combined effects of thermal and non-Newtonian character of lubricant on pressure, film profile, temperature rise and shear stress in EHL. Journal of Tribology. 109, 666-670. [48]Carslaw, H., Jaeger, J.C., 1959. Conduction of heat in solids. Oxford University Press: Oxford. [49]Bisset, E.J., Glander, D.W., 1998. A highly accurate approach that resolves the u6pressure spike of EHL. Transaction, ASME, Journal of Tribolog. 110, 241-246. [50]Venner, C.H., Ten Napel, W.E., 1989. Numerical calculation of the pressure spike in EHL. Lubrication Science. 2, 321-334.

Tags: