Mechanical, Electrical and Thermal Properties of Nylon-66/Flyash Composites: Effect of Flyash

Updata:01-01-1970

Source:
By:Authors

DOI: https://doi.org/10.30564/opmr.v4i2.5233

Abstract:
In the current study, the effect of flyash (FA) on the physic-mechanical, electrical, thermal and morphological behavior of nylon-66 (PA) was investigated. PA/FA composites were prepared by melt mixing via twin screw extruder, with varying weight percent (5 wt %, 10 wt %, 15 wt % and 20 wt %) of flyash. The results of composites were optimized and compared with virgin nylon-66. Mechanical and electrical properties of composites improved up to 10 wt% of FA loading without compromising the properties. The flyash filled nylon-66 composites showed a low abrasive wear rate. Increase the heat distortion temperature of composites with an increase in weight percent of flyash while opposing the melt flow rate. Flyash filler enhances the stiffness of plastics but significantly reduces the impact properties. Dispersion of flyash was examined by impact fracture surface of composites using a scanning electron microscope.
References:

[1]Ding, J., Ma, S., Shen, S., et al., 2017. Research and industrialization progress of recovering alumina from flyash: A concise review. Waste Management. 60, 375-387. [2]Chris-Okafor, P.U., Onwuka, C.O., Anekwe, O.J., et al., 2021. Impact of mixed fillers on the physicomechanical properties of flexible polyether foam. Organic Polymer Material Research. 3(1). [3]Bose, S., Mahanwar, P.A., 2004. Effect of flyash on the mechanical, thermal, dielectric, rheological and morphological properties of filled nylon 6. Journal of Minerals and Materials Characterization and Engineering. 3(02), 65. [4]Ahmad, Z., 2012. Polymer dielectric materials. Dielectric Material. DOI: https://doi.org/10.5772/50638. [5]Ez‐Zahraoui, S., Kassab, Z., Ablouh, E.H., et al., 2021. Effect of fly ash and coupling agent on the structural, morphological, thermal, and mechanical properties of polyamide 6/acrylonitrile‐butadiene‐ styrene blend. Polymer Composites. 42(7), 3518- 3538. [6]Liu, L., Liang, B., Wang, W., et al., 2006. Preparation of polyimide/inorganic nanoparticle hybrid films by sol-gel method. Journal of Composite Materials. 40(23), 2175-2183. [7]Venkatachalam, G., Kumaravel, A., 2017. Mechanical behaviour of aluminium alloy reinforced with sic/ flyash/basalt composite for brake rotor. Polymers & Polymer Composites. 25(3), 203-208. [8]Devi, M.S., Murugesan, V., Rengaraj, K., et al., 1998. Utilization of flyash as filler for unsaturated polyester resin. Journal of Applied Polymer Science. 69(7), 1385-1391. [9]Bonda, S., Mohanty, S., Nayak, S.K., 2012. Viscoelastic, mechanical, and thermal characterization of flyash‐ filled ABS composites and comparison of flyash surface treatments. Polymer Composites. 33(1), 22-34. [10]Cai, Z., Wang, X., Luo, B., et al., 2017. Dielectric response and breakdown behavior of polymerceramic nanocomposites: The effect of nanoparticle distribution. Composites Science and Technology. 145, 105-113. [11]Setsuda, R., Fukumoto, I., Kanda, Y., 2012. Effects of flyash in composites fabricated by injection molding. Polymer Composites. 33(8), 1351-1359. [12]Zhang, J., Du, Z., Zou, W., et al., 2017. MgO nanoparticles-decorated carbon fibers hybrid for improving thermal conductive and electrical insulating properties of Nylon 6 composite. Composites Science and Technology. 148(18), 1-8. DOI: https://doi.org/10.1016/j.compscitech.2017.05.008. [13]Ahmad, I., Mahanwar, P.A., 2010. Mechanical properties of flyash filled high density polyethylene. Journal of Minerals and Materials Characterization and Engineering. 9(03), 183. [14]American Society for Testing and Materials (ASTM) [Internet], 1997. Annual Book of ASTM Standards, Philadelphia, USA. Available from: https://www.astm.org/products-services/bos.html [15]Alaneme, K.K., Sanusi, K.O., 2015. Microstructural characteristics, mechanical and wear behaviour of aluminium matrix hybrid composites reinforced with alumina, rice husk ash and graphite. Engineering Science and Technology, an International Journal. 18(3), 416-422. [16]Rama, S.R., Rai, S.K., 2010. Studies on physicomechanical properties of flyash-filled hydroxyl-terminated polyurethane-toughened epoxy composites. Journal of Reinforced Plastics and Composites. 29(14), 2099-2104. [17]Chaowasakoo, T., Sombatsompop, N., 2007. Mechanical and morphological properties of flyash/ epoxy composites using conventional thermal and microwave curing methods. Composites Science and Technology. 67(11), 2282-2291. [18]Ramesan, M.T., 2014. Effect of flyash on thermal stability, flammability, oil resistance and transport properties of chlorinated styrene butadiene rubber composites. Journal of Elastomers & Plastics. 46(4), 303-324. [19]Fu, S.Y., Feng, X.Q., Lauke, B., et al., 2008. Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate–polymer composites. Composites Part B: Engineering. 39(6), 933-961. [20]Ramakrishna, H.V., Priya, S.P., Rai, S.K., 2006. Effect of flyash content on impact, compression, and water absorption properties of epoxy toughened with epoxy phenol cashew nut shell liquid-flyash composites. Journal of Reinforced Plastics and Composites. 25(5), 455-462. [21]Sreekanth, M.S., Joseph, S., Mhaske, S.T., et al., 2011. Effects of mica and flyash concentration on the properties of polyester thermoplastic elastomer composites. Journal of Thermoplastic Composite Materials. 24(3), 317-331. [22]Kilinçarslan, Ş., Türker, Y.Ş., 2020. Investigation of wooden beam behaviors reinforced with fiber reinforced polymers. Organic Polymer Material Research. 2(1). [23] Setsuda, R., Fukumoto, I., Kanda, Y., 2012. Effects of flyash in composites fabricated by injection molding. Polymer Composites. 33(8), 1351-1359.

Tags: